TM 10-4320-321-13&P
READ INSTRUCTIONS CAREFULLY BEFORE ATTEMPTING TO INSTALL, OPERATE OR SERVICE TEEL PUMPS.
FAILURE TO COMPLY WITH INSTRUCTIONS COULD RESULT IN PERSONAL INJURY AND/OR PROPERTY
DAMAGE! RETAIN INSTRUCTIONS FOR FUTURE REFERENCE.
Description
Teel self-priming centrifugal pumps are designed for continuous transfer pumping of chemicals from tanks and
sumps, and in chemical process and batch lines, waste water treatment and agricultural pumping applications.
Pumps self-prime (after filling pump casing) to 12 feet suction lift and will handle liquids with entrapped gases.
Maximum liquid temperature is 250°F for stainless steel units and 180°F for bronze units and maximum
viscosity is 100 SSU. See Pump Selection Guide. Pumps have 11/2" NPT suction and discharge ports
available in three flow ranges with balanced semi-open impellers which can handle some solids to 3/8"
diameter. Pumps use standard NEMA 56C frame, keyed shaft, 3450 RPM, CCW rotation motors. Pumps are
available with or without TEFC electric motors installed. Not for use with chemicals and/or solutions that can
set up, crystalize and/or solidify depending on temperature, atmospheric conditions, humidity, etc.
316 STAINLESS STEEL UNITS
Stainless steel pumps will handle many nonflammable liquids, acids, alkalis, caustics, trichlorethylene,
nonflammable solvents, brines and other fluids compatible with Type 316 stainless steel cast body and impeller
and Teflon mechanical seal. Units include Type 316 stainless steel shaft sleeve, hardware and adapter
bracket.
BRONZE UNITS
Bronze units handle some acids and organic material or any other liquid compatible with bronze and Viton
mechanical seal. Units include bronze body and impeller and Type 316 stainless steel shaft sleeve.
CLOSE COUPLED MODELS
Models 2P121 thru 2P125 and 2P373 thru 2P377 are completely assembled to Dayton 3450 RPM, 60 Hz
capacitor-start and 50/60 Hz 3-phase TEFC electric motors with 1.0 service factor. Pumps with single-phase
motors have automatic reset thermal protection. Pumps require field wiring.
PUMPING UNIT ONLY MODELS
Models 2P126 thru 2P128 and 2P377 thru 2P380 are not equipped with motors. They are suitable for mounting
to 3450 RPM, NEMA 56C face keyed shaft electric or air motors. The horsepower requirement of the motor
depends on the pump head selected, flow required and specific gravity of the fluid to be pumped. See
Centrifugal Pump Selection Guide (page 4) for assistance in selection of proper motor horsepower. All units
have stainless steel fasteners throughout. An optional Neoprene cartridge/Ni-Resist seat mechanical seal
assembly is available for pumping some caustic solutions with abrasive properties.
Unpacking
When unpacking the unit, inspect carefully for any damage that may have occurred during transit. Check for
loose, missing or damaged parts.
LIMITED WARRANTY
DAYTON ONE-YEAR LIMITED WARRANTY Teel stainless steel self-priming centrifugal pumps, Models 2P12l thru 2P128 & 2P373, thru 2P380, are warranted by Dayton Electric Mfg.
Co. (Dayton) to the original user against defects in workmanship or materials under normal use or one year after date of purchase. Any part which is determined by Dayton to be
defective in material or workmanship and returned to an authorized service location, as Dayton designates, shipping costs prepaid, will be, as the exclusive remedy, repaired or replaced
at Dayton's option. For limited warranty claim procedures, see PROMPT DISPOSITION below. This limited warranty gives purchasers specified legal rights which very from state to
state.
LIMITATION OF LIABILITY To the extent allowable under applicable law, Dayton's liability for consequential and incidental damages is expressly disclaimed. Dayton's liability in all
events is limited to, and shall not exceed, the purchase price paid.
WARRANTY DISCLAIMER. Dayton has made a diligent effort to illustrate nd describe the products in this literature accurately; however, such illustrations and descriptions are for the
sole purpose of identification, end do not express or imply a warranty that the products are merchantable, or fit for a particular purpose, or that the products will necessarily conform to
the illustrations or descriptions
Except as provided below, no warranty or affirmation of fact, expressed or implied, other then as stated in "LIMITED WARRANTY" above is made or authorized by Dayton.
PRODUCT SUITABILITY. Many states and localities have codes and regulations governing sales, construction, installation, and/or use of products for certain purposes, which may vary
from those in neighboring areas. While Dayton attempts to assure that its products comply with such codes, it cannot guarantee compliance, and cannot be responsible for how the
product is installed or used. before purchase and use of a product, please review the product application, and national and local codes and regulations, and be sure that the product,
installation, and use will comply with them.
Certain aspects of disclaimers are not applicable to consumer products; e.g.. (a) some states do not allow the exclusion or limitation of incidental or consequential damages, so the
above Imitation or exclusion may not apply to you; (b) also, some states do not allow limitations on how long an implied warranty lasts, consequently the above limitation may not apply
to you, and (c) by law, during the period of the Limited Warranty. any implied warranties of merchantability or fitness for a particular purpose applicable to consumer products purchased
by consumers, may not be excluded or otherwise disclaimed
PROMPT DISPOSITION. Dayton will make a good faith effort for prompt correction or other adjustment with respect to any product which proves to be defective within limited warranty.
For any product behaved to be defective within limited warranty, first write or call dealer from whom product was purchased. Dealer will give additional directions. If unable to resolve
satisfactory, write to Dayton at address below, giving dealer's name, address, date and number of dealer's invoice, and describing the nature of the defect. Title end risk of loss pass to
buyer on delivery to common carrier. If product was damaged in transit to you, file claim with carrier
Dayton Electric Mfg. Co., 5959 W. Howard St., Chicago, IL 60648
