CHAPTER 1 INTRODUCTION - TM-5-4930-228-14_99
figure 1-1 Tank and pump unit, with shipping dimensions
figure 1-2 Pumping assembly, front and rear view(sheet 1 of 2)
figure 1-2 Pumping assembly, front and rear view(sheet 2 of 2)
figure 1-3 Pumping assembly, front and rear, three-quarter view (sheet 1 of 2)
figure 1-3 Pumping assembly, front and rear, three-quarter view (sheet 2 of 2)
Figure 1-4. Pump and engine assembly, three-quarter view
Figure 1-5. Filter /separator flow chart.
Dimensions and Weights:
CHAPTER 2 OPERATING INSTRUCTIONS - TM-5-4930-228-14_109
Figure 2-1. Controls and instruments.
Starting - TM-5-4930-228-14_111
Figure 2-2. Engine starting instructions.
Unit Operation
Section II. 2-6. General OPERATION OF AUXILIARY EQUIPMENT
Section III. OPERATION UNDER UNUSUAL CONDITIONS
Operation in Dusty or Sandy Areas
CHAPTER 3 OPERATORS MAINTENANCE INSTRUCTIONS
Section II. 3-3. General To insure the tank and pump OPERATORS PREVENTIVE MAINTENANCE CHECKS AND SERVICES (PMCS)
Section III. OPERATORS TROUBLESHOOTING
Table 3-2. Operators Troubleshooting-continued
Filter / Separator Service
CHAPTER 4 ORGANIZATIONAL MAINTENANCE INSTRUCTIONS
Figure 4-1. Blocking instructions
Installation - TM-5-4930-228-14_125
Figure 4-2. Installing tanks and pump in truck (sheet 1 of 3)
Figure 4-2. Installing tanks and pump in truck (sheet 2 of 3)
Figure 4-2. Installing tanks and pump in truck (sheet 3 of 3).
figure 4-3 Tank and pump unit vertical tiedown strap assembly
Tank Vertical Tiedown
figure 4-4 Tank and pump vertical strap assembly installed (sheet 1 of 2)
figure 4-4 Tank and pump vertical strap assembly installed (sheet 2 of 2)
Section II. MOVEMENT TO A NEW WORKSITE - TM-5-4930-228-14_133
Table 4-1. Organizational Maintenance Preventive Maintenance Checks and Services
Table 4-2. Organizational Maintenance Troubleshooting
Section VI. RADIO INTERFERENCE SUPPRESSION
Figure 4-5. Pump and engine unit and muffler, removal.
Section VIII. ENGINE STARTING AND COOLING SYSTEM
Section IX. ENGINE IGNITION SYSTEM
Cleaning and Inspection - TM-5-4930-228-14_140
Figure 4-9. Magneto points and capacitor replacement.
Figure 4-10. Magneto drive gear, removal and installation
Section X. ENGINE FUEL SYSTEM - TM-5-4930-228-14_143
Air Cleaner and Bracket
Figure 4-14. Carburetor adjustment.
Figure 4-15. Governor controls, removal, and adjustment.
Section XI. EXHAUST MUFFLER AND ELBOW, OIL FILLER AND DRAIN PLUG, AND CRANKCASE BREATHER
Figure 4-17. Muffler and attaching hardware, exploded view
Section XII. FILTER / SEPARATOR, HOSES, NOZZLES, AND GROUND REEL
figure 4-20 filter/separator, removal
Cleaning and Inspection - TM-5-4930-228-14_151
figure 4-21 hose, nozzles, and bonding wires, removal and installation.
Cleaning and Inspection - TM-5-4930-228-14_153
figure 4-22 hose reels and spring housing, removal
Cleaning and Inspection - TM-5-4930-228-14_155
Figure 4-23. Nozzle, exploded view
Cleaning and Inspection. - TM-5-4930-228-14_157
Figure 4-24. Ground reel, removal.
Section XIII. INLET ELBOW, OUTLET TEE, AND MANIFOLD
Section XIV. TANKS
Figure 4-27. Tank assembly service.
Figure 4-28. Manhole cover, exploded view
Figure 4-29. Drain valve, exploded view
Discharge Valve Assembly
Figure 4-30. Discharge valve assembly, exploded view
Cleaning and Inspection - TM-5-4930-228-14_166
CHAPTER 5 DIRECT SUPPORT AND GENERAL SUPPORT MAINTENANCE INSTRUCTIONS
Table 5-1. Direct Support and General Support Maintenance Troubleshooting-continued
Table 5-3. Repair and Replacement Standards
CHAPTER 6 REPAIR INSTRUCTIONS
Figure 6-2. Pump and intermediate coupling, disassembly and reassembly
Section II. ENGINE COMPONENTS
Figure 6-3. Engine assembly removal
Figure 6-5. Cylinder head removal.
Figure 6-6. Cylinder head bolts tightening sequence
Valve Inspection Cover and Tappets
Clean all carbon out of the insert
Figure 6-9. Engine base and oil pump removal.
Figure 6-10. Engine base and oil pump, exploded view
Piston and Connecting Rod
Crankshaft
Camshaft and Governor Assembly
Section III. FILTER / SEPARATOR
Figure 6-16. Filter / separator, exploded view
Section IV. HOSE REEL ASSEMBLY
Figure 6-17. Hose reel, disassembly.
Section V. TANKS AND FRAME
Protective Finish
APPENDIX A REFERENCES - TM-5-4930-228-14_191
APPENDIX B MAINTENANCE ALLOCATION CHART - TM-5-4930-228-14_193
Section II. MAINTENANCE ALLOCATION CHART - TM-5-4930-228-14_194
Section II. MAINTENANCE ALLOCATION CHART
Section II. MAINTENANCE ALLOCATION CHART - TM-5-4930-228-14_196
Section IV. REMARKS
ALPHABETICAL INDEX - TM-5-4930-228-14_199
ALPHABETICAL INDEX - TM-5-4930-228-14_200
figure 1-1 Tank and pump unit, with shipping dimensions
figure 1-2 Pumping assembly, front and rear view(sheet 1 of 2)
figure 1-2 Pumping assembly, front and rear view(sheet 2 of 2)
figure 1-3 Pumping assembly, front and rear, three-quarter view (sheet 1 of 2)
figure 1-3 Pumping assembly, front and rear, three-quarter view (sheet 2 of 2)
Figure 1-4. Pump and engine assembly, three-quarter view
Figure 1-5. Filter /separator flow chart.
Dimensions and Weights:
CHAPTER 2 OPERATING INSTRUCTIONS - TM-5-4930-228-14_109
Figure 2-1. Controls and instruments.
Starting - TM-5-4930-228-14_111
Figure 2-2. Engine starting instructions.
Unit Operation
Section II. 2-6. General OPERATION OF AUXILIARY EQUIPMENT
Section III. OPERATION UNDER UNUSUAL CONDITIONS
Operation in Dusty or Sandy Areas
CHAPTER 3 OPERATORS MAINTENANCE INSTRUCTIONS
Section II. 3-3. General To insure the tank and pump OPERATORS PREVENTIVE MAINTENANCE CHECKS AND SERVICES (PMCS)
Section III. OPERATORS TROUBLESHOOTING
Table 3-2. Operators Troubleshooting-continued
Filter / Separator Service
CHAPTER 4 ORGANIZATIONAL MAINTENANCE INSTRUCTIONS
Figure 4-1. Blocking instructions
Installation - TM-5-4930-228-14_125
Figure 4-2. Installing tanks and pump in truck (sheet 1 of 3)
Figure 4-2. Installing tanks and pump in truck (sheet 2 of 3)
Figure 4-2. Installing tanks and pump in truck (sheet 3 of 3).
figure 4-3 Tank and pump unit vertical tiedown strap assembly
Tank Vertical Tiedown
figure 4-4 Tank and pump vertical strap assembly installed (sheet 1 of 2)
figure 4-4 Tank and pump vertical strap assembly installed (sheet 2 of 2)
Section II. MOVEMENT TO A NEW WORKSITE - TM-5-4930-228-14_133
Table 4-1. Organizational Maintenance Preventive Maintenance Checks and Services
Table 4-2. Organizational Maintenance Troubleshooting
Section VI. RADIO INTERFERENCE SUPPRESSION
Figure 4-5. Pump and engine unit and muffler, removal.
Section VIII. ENGINE STARTING AND COOLING SYSTEM
Section IX. ENGINE IGNITION SYSTEM
Cleaning and Inspection - TM-5-4930-228-14_140
Figure 4-9. Magneto points and capacitor replacement.
Figure 4-10. Magneto drive gear, removal and installation
Section X. ENGINE FUEL SYSTEM - TM-5-4930-228-14_143
Air Cleaner and Bracket
Figure 4-14. Carburetor adjustment.
Figure 4-15. Governor controls, removal, and adjustment.
Section XI. EXHAUST MUFFLER AND ELBOW, OIL FILLER AND DRAIN PLUG, AND CRANKCASE BREATHER
Figure 4-17. Muffler and attaching hardware, exploded view
Section XII. FILTER / SEPARATOR, HOSES, NOZZLES, AND GROUND REEL
figure 4-20 filter/separator, removal
Cleaning and Inspection - TM-5-4930-228-14_151
figure 4-21 hose, nozzles, and bonding wires, removal and installation.
Cleaning and Inspection - TM-5-4930-228-14_153
figure 4-22 hose reels and spring housing, removal
Cleaning and Inspection - TM-5-4930-228-14_155
Figure 4-23. Nozzle, exploded view
Cleaning and Inspection. - TM-5-4930-228-14_157
Figure 4-24. Ground reel, removal.
Section XIII. INLET ELBOW, OUTLET TEE, AND MANIFOLD
Section XIV. TANKS
Figure 4-27. Tank assembly service.
Figure 4-28. Manhole cover, exploded view
Figure 4-29. Drain valve, exploded view
Discharge Valve Assembly
Figure 4-30. Discharge valve assembly, exploded view
Cleaning and Inspection - TM-5-4930-228-14_166
CHAPTER 5 DIRECT SUPPORT AND GENERAL SUPPORT MAINTENANCE INSTRUCTIONS
Table 5-1. Direct Support and General Support Maintenance Troubleshooting-continued
Table 5-3. Repair and Replacement Standards
CHAPTER 6 REPAIR INSTRUCTIONS
Figure 6-2. Pump and intermediate coupling, disassembly and reassembly
Section II. ENGINE COMPONENTS
Figure 6-3. Engine assembly removal
Figure 6-5. Cylinder head removal.
Figure 6-6. Cylinder head bolts tightening sequence
Valve Inspection Cover and Tappets
Clean all carbon out of the insert
Figure 6-9. Engine base and oil pump removal.
Figure 6-10. Engine base and oil pump, exploded view
Piston and Connecting Rod
Crankshaft
Camshaft and Governor Assembly
Section III. FILTER / SEPARATOR
Figure 6-16. Filter / separator, exploded view
Section IV. HOSE REEL ASSEMBLY
Figure 6-17. Hose reel, disassembly.
Section V. TANKS AND FRAME
Protective Finish
APPENDIX A REFERENCES - TM-5-4930-228-14_191
APPENDIX B MAINTENANCE ALLOCATION CHART - TM-5-4930-228-14_193
Section II. MAINTENANCE ALLOCATION CHART - TM-5-4930-228-14_194
Section II. MAINTENANCE ALLOCATION CHART
Section II. MAINTENANCE ALLOCATION CHART - TM-5-4930-228-14_196
Section IV. REMARKS
ALPHABETICAL INDEX - TM-5-4930-228-14_199
ALPHABETICAL INDEX - TM-5-4930-228-14_200
