CHAPTER 1 INTRODUCTION - TM-5-4320-215-12_24
Figure 1. Centrifugal pump, right rear, three-quarter view
Figure 1. Centrifugal pump, left front, three-quarter view, with shipping dimensions.
Table 1. Maintenance and Operating Supplies
Figure 3. Practical wiring diagram.
CHAPTER 2 INSTALLATION AND OPERATING INSTRUCTIONS
Figure 4. Batteries, cables, and battery box, removal and installation
Section II. MOVEMENT TO NEW WORKSITE
Figure 5. Controls and instruments.
Figure 6. Pump priming instructions.
Figure 7. Engine starting instructions.
Figure 8. Engine stopping instructions
Section IV. OPERATION UNDER UNUSUAL CONDITIONS - TM-5-4320-215-12_36
Section V. OPERATION OF MATERIEL USED IN CONJUNCTION WITH THE PUMPING UNIT
CHAPTER 3 OPERATOR AND ORGANIZATIONAL MAINTENANCE INSTRUCTIONS
Figure 9. Lubrication order.
Figure 9. Continued - TM-5-4320-215-12_40
Figure 9. Continued - TM-5-4320-215-12_41
Section II. PREVENTIVE MAINTENANCE SERVICES
Figure 10. Operators daily services
Figure 10. Continued
33. Quarterly Preventive Maintenance Service
ENGINE-Continued - TM-5-4320-215-12_46
ENGINE-Continued - TM-5-4320-215-12_47
ENGINE-Continued - TM-5-4320-215-12_48
Section IV. RADIO INTERFERENCE SUPPRESSION
Section V. CENTRIFUGAL PUMP AND ENGINE REMOVAL AND INSTALLATION
Figure 12. Centrifugal pump, grease cup, reducer, and nipple, removal and installation.
Section VI. FUEL AND EXHAUST SYSTEMS
Figure 15. Fuel tank and fuel line, removal and installation.
Section VII. ELECTRICAL SYSTEM
50. Generator and Adjusting Support
Figure 19. Generator and voltage regulator, on-engine testing.
Figure 20. Generator and adjusting support, removal and installation.
Figure 22. Voltage regulator, cleaning and inspection.
Figure 23. Voltage regulator continuity test.
Figure 24. Voltage regulator mechanical adjustment.
Figure 25. Voltage regulator electrical adjustment.
Figure 25. Continued. - TM-5-4320-215-12_62
Figure 25. Continued. - TM-5-4320-215-12_63
Section VIII. LUBRICATION SYSTEM
Figure 27. Tongue and cart foot, removal and installation
Figure 18. Reflector, wheel chock, lunette, and lifting bail, removal and installation
Section X. WHEELS, TIRES, AND TUBES
Figure 20. Wheel, hub, and bearing, removal and installation.
CHAPTER 4 DEMOLITION OF THE PUMPING UNIT TO PREVENT ENEMY USE
Figure 32. Placement of charges
CHAPTER 5 SHIPMENT AND LIMITED STORAGE
c. Operation.
APPENDIX I REFERENCES
8. Supply Publications
APPENDIX II MAINTENANCE ALLOCATION
MAINTENANCE ALLOCATION CHART - TM-5-4320-215-12_76
MAINTENANCE ALLOCATION CHART -CONT - TM-5-4320-215-12_77
MAINTENANCE ALLOCATION CHART -CONT - TM-5-4320-215-12_78
MAINTENANCE ALLOCATION CHART -CONT - TM-5-4320-215-12_79
APPENDIX III BASIC ISSUE ITEMS
Section II. BASIC ISSUE ITEMS LIST
BASIC ISSUE ITEMS LIST -CONT
INDEX
INDEX -CONT - TM-5-4320-215-12_84
INDEX -CONT - TM-5-4320-215-12_85
Figure 1. Centrifugal pump, right rear, three-quarter view
Figure 1. Centrifugal pump, left front, three-quarter view, with shipping dimensions.
Table 1. Maintenance and Operating Supplies
Figure 3. Practical wiring diagram.
CHAPTER 2 INSTALLATION AND OPERATING INSTRUCTIONS
Figure 4. Batteries, cables, and battery box, removal and installation
Section II. MOVEMENT TO NEW WORKSITE
Figure 5. Controls and instruments.
Figure 6. Pump priming instructions.
Figure 7. Engine starting instructions.
Figure 8. Engine stopping instructions
Section IV. OPERATION UNDER UNUSUAL CONDITIONS - TM-5-4320-215-12_36
Section V. OPERATION OF MATERIEL USED IN CONJUNCTION WITH THE PUMPING UNIT
CHAPTER 3 OPERATOR AND ORGANIZATIONAL MAINTENANCE INSTRUCTIONS
Figure 9. Lubrication order.
Figure 9. Continued - TM-5-4320-215-12_40
Figure 9. Continued - TM-5-4320-215-12_41
Section II. PREVENTIVE MAINTENANCE SERVICES
Figure 10. Operators daily services
Figure 10. Continued
33. Quarterly Preventive Maintenance Service
ENGINE-Continued - TM-5-4320-215-12_46
ENGINE-Continued - TM-5-4320-215-12_47
ENGINE-Continued - TM-5-4320-215-12_48
Section IV. RADIO INTERFERENCE SUPPRESSION
Section V. CENTRIFUGAL PUMP AND ENGINE REMOVAL AND INSTALLATION
Figure 12. Centrifugal pump, grease cup, reducer, and nipple, removal and installation.
Section VI. FUEL AND EXHAUST SYSTEMS
Figure 15. Fuel tank and fuel line, removal and installation.
Section VII. ELECTRICAL SYSTEM
50. Generator and Adjusting Support
Figure 19. Generator and voltage regulator, on-engine testing.
Figure 20. Generator and adjusting support, removal and installation.
Figure 22. Voltage regulator, cleaning and inspection.
Figure 23. Voltage regulator continuity test.
Figure 24. Voltage regulator mechanical adjustment.
Figure 25. Voltage regulator electrical adjustment.
Figure 25. Continued. - TM-5-4320-215-12_62
Figure 25. Continued. - TM-5-4320-215-12_63
Section VIII. LUBRICATION SYSTEM
Figure 27. Tongue and cart foot, removal and installation
Figure 18. Reflector, wheel chock, lunette, and lifting bail, removal and installation
Section X. WHEELS, TIRES, AND TUBES
Figure 20. Wheel, hub, and bearing, removal and installation.
CHAPTER 4 DEMOLITION OF THE PUMPING UNIT TO PREVENT ENEMY USE
Figure 32. Placement of charges
CHAPTER 5 SHIPMENT AND LIMITED STORAGE
c. Operation.
APPENDIX I REFERENCES
8. Supply Publications
APPENDIX II MAINTENANCE ALLOCATION
MAINTENANCE ALLOCATION CHART - TM-5-4320-215-12_76
MAINTENANCE ALLOCATION CHART -CONT - TM-5-4320-215-12_77
MAINTENANCE ALLOCATION CHART -CONT - TM-5-4320-215-12_78
MAINTENANCE ALLOCATION CHART -CONT - TM-5-4320-215-12_79
APPENDIX III BASIC ISSUE ITEMS
Section II. BASIC ISSUE ITEMS LIST
BASIC ISSUE ITEMS LIST -CONT
INDEX
INDEX -CONT - TM-5-4320-215-12_84
INDEX -CONT - TM-5-4320-215-12_85
