S u b j e c t ,     P a r a Subject, Para Q TM  10  4320-343-14 S R Receipt    of    material,    service    upon    4.4 Recommendation of equipment improvement, 1.5 Reflector    maintenance,    4.17.3 Regulated pump maintenance Actuating    rod    and    actuator    level maintenance     4.14.6 Actuator and bracket maintenance, 4.14.5 Control  box  test,  4.14.4 Magnetic   pickup   maintenance,   4.14.3 Pressure controller removal, 4.14.2 Pressure regulator cable assemblies maintenance,   4.14.1 Regulator assembly maintenance, 4.14 Run  relay  K2  replacement,  4.13.11 Regulated pumping assembly operation Shutdown    for    regulated    model (ADC15OO),   2.5.2.2 Starting    and    shutdown    for    regulated    model (ADC15OO)m 2.5.2 Starting  for  regulated  model  (ADC1506),  2.5.2.1 Regulator assembly maintenance Actuating    rod    and    actuator    level maintenance, 4.14.6 Actuator and bracket maintenance, 4.14.5 Control  box  test,  4.14.4 Magnetic   pickup   maintenance,   4.14.3 Pressure controller removal, 4.14.2 Regulator assembly maintenance (continued) Regulator assembly maintenance, 4.14 Repair     parts,     4.3,     5.3,6.3 Rocker  arm  assembly  repair,  6.6.3 Run   relay   (K2)   replacement,   4.13.9 Run   relay   W   replacement,   4.13.11 Safety   relay   (K1)   base   replacement,   4.13.8 Safety   relay   K1   replacement,   4.13.7 Scope, 1.1 Service    upon    receipt    of    material,    4.4 Shutdown for nonregulated models, 2.5.1.2 Shutdown   for   regulated   model   (ADC1500),   2.5.2.2 Shutdown solenoid maintenance, 4.10.15 Shutdown solenoid test, 4.10.14 Sleeve  and  rotating  assembly  maintenance,  5.6.4 Spark arrestor maintenance, 4.9.1 Special   tools   and   support   equipment,   4.2,5.2,6.2 Starter   assembly   maintenance,   4.10.13 Starting    and    shutdown    for    nonregulated    pumps,    2.5.1 Starting    and    shutdown    for    regulated    model (ADC1500), 2.5.2 Starting for nonregulated models, 2.5.1.1 Starting   for   regulated   model   (ADC1500)   2.5.2.1 Storage preparation, 1.6 Storage, 4.21 Suction  (7),  2.1.7 Suction   gauge   (M4),   4.13.6 Suction  manifold  maintenance,  4.15.3 Support  equipment  and  tools,  special  4.2,  5.2,6.2 Support  leg  maintenance,  4.17.5 Switch   emergency   stop   (St)   replacement,   4.13.3 T Tachometer/hourmeter    (5)    2.1.5 Tachometer/hourmeter (M3), replacement Test equipment,   and   materials,   required   for installation,    4.5.1 Throttle (10),2.1.10 Throttle    control    assembly    maintenance,    4.11 Tire  maintenance,  4.17.1 Tool     box     maintenance,     4.17.6 Tools  and  equipment,  common  4.1,  5.  1,6.1 Tools    and    support    equipment,    special    4.2,    5.2,    6.2 Tools    installation,    4.5.1 Top  dead  center,  5.5.9 Change 2 index-9